Bernhards Random Ramblings BACKUP

[ Hallelujah Paper posts ] While I do need more conveyor belt assemblies , it looks like the plan to integrate foreground models and backdrop industry might work out nicely.

As I'm getting off the bus tonight, I see something moving under the bus. ...  Look at that, a young gopher snake, a bit over 12 inches long. What is it doing under the bus? According to the driver it's not unusual for a snake to hitch a ride on a parked bus and drop off when it finally stops again. Once the bus had left, I moved it off the street into a nearby bush.

I've set up the portable command station in the office. Works as intended. However, I'm having trouble connecting the NCE AIU to the NCE cab bus so that train detection works properly. JMRI sees the feedback from the AIU, but sensors don't change state when the board LEDs indicate a train. More debugging needed. Update: Now that I had some time to think about this ... I believe I merely used the wrong sensor numbers. It's not NS0 - NS13, but rather NS48 - NS61. I have the AIU on cab ID=4, and the sensor IDs are calculatd as (cab ID - 1) * 16 + input - 1. I'll check this out when I'm back in the office after the long weekend. As a side-note, NCE AIU is supported with the NCE USB interface version 7 when used with PowerCab version 1.65 or higher.

This turkey family is easy to tell apart from the other flocks. There's only one adult, and she still has all 4 chicks .

As part of a work event I went kayaking on Monterey Bay. It was a beautiful day along the shore line. We saw plenty of otters, sea lions, harbor seals, and tons of birds. We started in Monterey harbor and paddled around the breakwater along the shoreline towards the aquarium. Several otters were quite active in the kelp beds close to shore. We passed them on the ocean side, so the background in the photo below is not particularly appealing, yet typical for this section of the coast. I loved how the cormorants hang out on the rocks right next to a few harbor seals. As usual, Hopkins Research Station was the turn-around point for our group. More cormorants. Once again, a smart phone is not a good camera for wildlife photography. More otters. Most sea otter encounters looked more like this, rather than the first otter picture. Sea lions and birds on the breakwater. We were a fast group and had some spare time, so we paddled around some more inside the harbor. Kelp beds from the shore. Wha...

Wait a second ... What's that? ... Yep, definitely a young bobcat. I haven't seen one for a while .

The Greenly Northern, my office layout, so far had a Raspberry Pi3 hardwired to the layout along with my NCE PowerCab. I described how I set that up in a post last fall . I wanted the layout control to be more portable and more flexible. E.g. take home the layout box, Pi with JMRI, and PowerCab over the weekend for comfortable programming at the work bench. Or maybe in the future take it to a show easily. I decided that the occupancy sensors and the detector board are part of the layout. However, the NCE PowerCab track connection and the USB interface, as well as the Raspberry Pi need to be easy to transport. While at it, I also wanted a portable screen for the Pi. At first I planned to pack everything into the same small tool case I use for the Mobile Station,  and quickly realized that screen and electronics would fit, but the power supplies would not, so I decided to go for a larger aluminum case . The build quality of the case I chose doesn't come close to the black aluminum ca...

One more server and the TV computer still to go. Next weekend.

For this month's ops session at Silicon Valley Lines Franziska joined me in running Bayshore Yard. She's been to SVL a couple times since that first session 2 years ago  and it shows. She ran the yard switcher, moved engines in and out of the engine facility, and even classified an incoming train with some guidance. This allowed me to chat with several visitors we had at the session tonight, and we still finished all the work at Bayshore Yard. I could not have done that without her. Unfortunately I left my current smartphone at home, so the camera in the old phone I use as throttle had to do.

[ Hallelujah Paper posts ] I didn't quite realize that the Walthers conveyor kit only has about 15 inches of conveyor segments in the package and I need on the order of 4 or 5 feet. More conveyors are needed. Oh well, the good thing is I did something different tonight.

Despite its name, Maerklin's Mobile Station is anything but. It's hard-wired to the track control box which is hard-wired to the track. I'm using the Mobile Station primarily to program MFX locomotives at the work bench, but on occasion I can see myself taking it somewhere else, or wanting to run a diorama style layout. Also, since I don't really have a permanent work area everything is portable . Hence the Mobile Station and track connection box need to be portable, too. I picked up a small tool case at Harbor Freight and mounted the track box inside. The layout connection is terminated on a RCA plug. The Mobile Station and power supply neatly fit inside the padded case. To test locomotives, or in the future run trains, I plug a modified RCA cable into the socket, and use clamps to hook it to the track. Plug in the power supply, grab the Mobile Station and we're ready to go. When I'm done for the day, I unplug the power supply, and store it with the Mobile Sta...

Due to a late meeting I missed my bus connection tonight and ended up taking Caltrain home. Train #264 arrived in Mountain View 3 minutes late, i.e. basically on time. I had a choice to wait in Mountain View for #268 which would take me down to Blossom Hill, or change trains in San Jose. San Jose has more variety of traffic, so I took #264 down to Diridon station and hung out on the platform until it was time to catch #268 for the ride home. I have not transferred between trains in San Jose for a while and did not expect that south-bound trains are now leaving from the newly built platform 6 that opened several years ago. I ended up asking a conductor who looked at me funny when I said that the Gilroy train normally leaves from track 5, no? "Uh, no sir, it's been leaving from track 6 for quite some time now."  Right. That was 15 years ago, when I was commuting to South San Francisco, before Caltrain introduced the Baby Bullet service ...

For tonight's B&O ops session, I opted for Williams Street Yard, which can get very busy and if the yard master is not careful he can completely gum up the railroad.  Williams Street "Yard" is basically a siding, a stub end track, and the River Interchange to the Western Maryland's Ridgley Yard in the foreground in the photo above. Since this was the first time I ran Williams Street, I did manage to completely gum up the railroad and made several trains wait for 30+ minutes at the towers around Cumberland station while trying to service train BO11. It didn't help that a local was in town, and one of the towers had trouble with their JMRI CTC machine and couldn't throw turnouts for a while. At Williams Street, the yard master needs to think ahead and position cars and switcher engines for the servicing tasks at hand before the respective train arrives in the station. This is very similar to how I envision operations at Backnang station on the future Murrba...

[ BR 601 posts ] Slowly, but surely everything is finding its place. The PowerPack moved into the rear of the cab on top of the decoder. It turned out that the niche inside the loco nose didn't have enough space for the capacitor. I cut down the speaker baffle to fit the speaker between chassis and roof. I just need to decide how to keep it solidly in place, yet removable. I will use the red cross bar behind the cab to consolidate wiring for head and tail lights as well as mounting the cab light.

Great coffee. Hand-made. Hand-delivered. Enjoyed in California.

I'm running several servers and network infrastructure at home. We rarely use desktop computers anymore, since the family has basically moved towards Laptops, Chromebooks, tablets, and phones for their technology needs (with the exception of the PC Gaming station). However, those devices along with entertainment equipment still want to be supported and connected to the Internet by ... something. At the very least for in-house backups and redundant storage. Cloud services for photos are all nice and good, but with volume they become expensive. Backup providers are shifting on an almost yearly basis in search of a viable business model. I haven't touched much the infrastructure for quite a while. It worked well enough so there wasn't really a need. "Don't touch a running system" is for lazy system administrators that rather play with their trains. However, things started to get a bit creaky over time. Newer software versions complained about the OS being too old...

It's the middle of summer. Time for the annual panel cleaning. I usually clean the solar panels in late July, early August. The winter rains keep them reasonably clean for the other half of the year, but by the middle of the summer enough dust, dirt, and gunk has baked on the panels that they can use some love. Cleaned panel on the left, dirty panel on the right. I wash the panels with a hose, wipe them off with a rag, and finally wash off the remaining dirt. It's getting pretty hot up here in late morning, so I should get back to work. The result is below. If you look closely, you can see that the two panels in the top left corner have some gunk left near the top edge, since I couldn't safely reach that corner with the rag.

[ BR 601 posts ] I hate soldering an ESU PowerPack to the Loksound 4 decoder. Given the circumstances, this is pretty well done with reasonably sized solder pads, but I really don't like soldering on a $100+  decoder board. Once that was done and visually inspected, I connected speaker and a motor to the decoder and fired up the Mobile Station to double-check proper operation. Let capacitor charge for a couple minutes, fire up the speaker, disconnect the lead, aaaaaand ... urgh. Nothing. Yes, the motor is the one I replaced from Roco 43012 I verified the programming of CV 113, which controls how long the decoder pulls power from the capacitor. It was zero. Well, yeah, that's not going to work. Re-program to 150. Let charge. Try again, aaaaaand ... nothing. Urgh! No matter what I programmed into CV 113, it was zero when I read the value back out. Alright. Something is preventing the decoder from accepting the PowerPack. I double-checked my solder connections. All good. Scratche...

My very first digital Maerklin locomotive was a BR86 from a starter set. This model is known to have problems with power pickup, and sounding like it's grinding up its gears. Part of the issue here is the very low-end MM2 decoder built into these locomotives. Nevertheless, I lived with it for the last 10 years, but the locomotive got less and less use as other, cooler locomotives arrived on the Welztalbahn or were converted from analog. When switching a local freight this afternoon, I got fed up about the noise and crappy driving habits of this locomotive and brought it to the work bench. The axles got some more oil, the gears some grease, and it ran a little bit quieter, but not a lot. Alright, I do have a couple spare LokPilot 3.0 sitting on a shelf. Today's the day! The old MM2 decoder made way for a Lokpilot, I connected power pickup and motor leads to see if this truly makes a difference... and what a difference it makes! The drivetrain no longer aches and croaks, but pur...